Products
Art Gallery Mounting/Installation Work Station
This case was built for the Garth Greenan Gallery as a mobile work station used in art mounting and gallery installations. The case lid features a tilting frame that has 3 rods for mounting paper rolls. The frame is designed to hold 3 rolls of paper that are 6” diameter. For easier access, the frame tilts forward. It is secured with a cable latch with a central pull handle that secures the frame at the left and right side. The case lid is held in position with gas springs.
Dante/Network Power Inlet Box
This inlet box is designed to be a main signal point for work stations and racks using the Dante protocol. The box features 3 Neutrik NE8FDP-B Cat5 jacks labeled “primary”, “secondary”, and “network”. The jacks are intended to bring Dante Primary, Secondary, and a main network signal into a work station. The power portion of the box features a recessed Hubbell inlet wired to a duplex outlet. This box can be mounted behind a Penn D0047Z cable hatch. The box provides a neat “all in one” location for portable systems.
Penn State Side Line Helmet Repair Work Station
This case was designed for Penn State University as a side line helmet repair work station. The trunk features 12 Tilt Lock bins mounted in the lid. Each Tilt Lock bin features 3 individual storage compartments each, for a total of 36 individual compartments. The case lid also features a cordless drill storage compartment with a clear Lexan door. The drill’s battery charger is also mounted in the lid for quick access. A 6 outlet power strip is located in the center of the lid to provide easy access to power. The power strip is hard wired to a recessed male Hubbell inlet located on the back of the case. The case lid also features colored LED tape lights allowing for visibility in low lit environments.
5 Drawer Production Workbox w/Hinged Lid & Flip Up Shelf
This case was built for Applied Audio as a generic catch all work box. The outer case is built out of ½” plywood laminated with your choice of ABS plastic colors. Each drawer is built out of ½” Baltic Birch and is mounted on HD Accuride drawer glides. The drawers feature a ½” plywood face with a recessed handle as a pull. All drawer edges are routed. The drawers are coated with clear lacquer inside and out.
Nikon D810 Camera System Pelican 1510 Case
This case was built for Elevate Life Church to hold a Nikon D810 camera body and lens kit.
Sony Camera Chain Case
This case was designed for AVI-SPL to hold a Sony camera system. The case holds all camera components for rental applications including the camera body, preview monitor, lenses, camera control unit, cable reel and Telex com head set.
Chauvet Geyser RGB Fog Machine Case
Custom ATA road case designed to safely transport six Chauvet Geyser RGB fog machines for Audio Images. Each fixture is secured upside down in precision CNC-cut foam to allow clamps to remain attached for faster setup. The case features a removable dual-layer tray system, a rear carpet-lined accessory compartment, rugged 3/8” plywood construction with black ABS laminate, recessed hardware, stacking caster cups, and heavy-duty 4” casters for tour-ready durability and efficient truck pack.
Custom Portable TV Panel Work Station
This case was built for MIT as a portable work station for a Tricaster system. The case lid features a centered tilting monitor mount allowing the user to supply their own monitor. The main work surface features a slide out shelf for the Tricaster panel. A 17RU rack section is mounted below for equipment storage. Four storage drawers are included next to the rack section.
24 Space Insert / Surround Rack Set
This case set was built for PRG. The case features a removable 24RU inner rack shell and a custom exterior case.
Black Magic SmartView Monitor Fly Pack Storm Case
This case was built for Paramount Event Group as a custom video fly pack. The case features a 6RU tilting rack frame for a Black Magic Smartview Monitor. Below the monitor is a 3RU rack section for additional equipment storage. A custom foam insert is included to hold Datavideo DAC 70’s and Decimator MD-HX converters.
Integrated Portable Church Drum Set Transport - Riser Case
This custom Drum Set Transport Case with Integrated Riser Platform was built for City Church as a complete storage, transport, and performance solution. The case allows a fully assembled drum kit to remain largely intact during transport and converts into a full-size drum riser by deploying a hinged rear platform with removable leveling feet.
Constructed from ½” plywood laminated in black ABS and riding on heavy-duty Colson locking casters, the carpet-lined platform eliminates the need for a separate drum rug while securely supporting pedals and hardware. Designed specifically for portable and shared church environments, this system significantly reduces weekly setup time while maintaining professional durability and presentation.
3000w Rack Mounted US To EU Power Converter Box
This power conversion box is designed to be a main power input for touring systems that travel between the US and EU. The box is split into two independent sides:
San Diego State Side Line Helmet Repair Tech Work Box
This trunk was built for San Diego State University. The trunk is designed to provide a mobile tool station to be used on a football sideline.
Tennessee Titans Athletic Trainer’s Sideline Trunk
This trunk was designed for the Tennessee Titans football athletic training department. The trunk is designed as trunk for general storage. The trunk features 4 drawers built into an isolated inner shell that separates them from the exterior case. Each drawer is built out of ½” Baltic Birch plywood and is mounted on HD Accuride glides.
Tennessee Titans Athletic Trainers Storage Trunk
This trunk was designed for the Tennessee Titans football athletic training department. The trunk is designed as a trunk for general storage. The trunk features 5 drawers. Each drawer is built from ½” Baltic Birch plywood and mounted on HD Accuride drawer glides. The top left 2 drawers each feature 4 compartments with removable ½” marine grade black plastic dividers. Each compartment is 4” wide x 21.5” deep x 7” tall. The middle third drawer is split into quadrants. Each quadrant measures 8.625” wide x 10.375” deep x 13” tall. The bottom 2 drawers are split into 16 compartments each with removable dividers. When the drawer is configured into 16 compartments; each compartment measures: 4” wide x 5” deep x 13” tall.